Accessories

The ATTE goes into a Flash Head where the Flashtube normally goes and adds about an inch to the position of the Flashtube from the face of the Head. This is generally preferred when you need a different coverage from a custom reflector than the tube provides from it's normal location.

This coiled extension cord for the Lumedyne Heads is about 3 feet long before you start to stretch it and can easily stretch to about 7 feet. It has the silver round Head plugs at each end; one male for the Pack end and one female for the Head end. This is a direct Head Cord for the Signature Heads and an extension cord for the other Heads that have a cord already.

This is the normal replacement bulb for the glowing modeling light in the center of the Lumedyne Modeling style Flashtubes. It is about 25 watts bright and does use your battery at a rate of one 200ws flash per 20 seconds of modeling light use. It is user replaceable by simply first removing the flashtube then pulling the burned out bulb straight out. After carefully replacing the AMBR into its legs, the flashtube fits around it and plugs back into place.

This is the high performance replacement bulb for the glowing modeling light in the center of the Lumedyne Modeling style Flashtubes. It is about 25 watts but is almost 50% brighter than a normal Halogen bulb. So for the same drain as our other AMBR bulb this one is a bit brighter. It does also use your battery at a rate of one 200ws flash per 20 seconds of modeling light use. This AMBX bulb is also more durable against high temperature for extended use or high power flashes or rapid flashes where in all cases more than the normal heat is involved and a normal bulb would frost over white and fail due to overheating. It is user replaceable by simply first removing the flashtube then pulling the burned out bulb straight out. After carefully replacing the AMBX into the Head's legs, the flashtube fits around it and plugs back into place.

AFSE Flashtubes fit all of the standard Flash Heads such as the Classic #001 and #002 Heads that had no modeling light feature. They also fit the new Extra Small Basic Heads HSBC. The Flashtubes push/pull straight in/out and they will last for tens of thousands of flashes or one face down fall onto a hard surface. Any of the Heads that have a modeling light would use the AFTE instead of this one.

AFTE Flashtubes fit all of the existing Lumedyne Flash Heads with or without the modeling light feature. They also fit in the new Extra Small Heads. They can be used at low power as well but should not be used above 800ws per Head as that is the upper rating of this flashtube's performance. The Flashtubes push/pull straight in/out and they will last for tens of thousands of flashes or one face down fall onto a hard surface. Any of the Heads can use this flashtube, however, the modeling lamp itself is separate and this flashtube does not convert a non-modeling Head to have that feature.

AFTQ 2400ws Quartz Flashtubes fit all of the existing Lumedyne Flash Heads with or without the modeling light feature. They also fit in the new Extra Small Heads. They can be used at low power as well and can be used up to 2,400ws as that is the upper rating of this flashtube's performance. The Flashtubes push/pull straight in/out and they will last for tens of thousands of flashes or one face down fall onto a hard surface. Any of the Heads can use this flashtube, however, the modeling lamp itself is separate and this flashtube does not convert a non-modeling Head to have that feature.

AFSQ 2400ws Quartz Flashtubes fit all of the standard Flash Heads such as the Classic #001 and #002 Heads that had no modeling light feature. They also fit the new Extra Small Basic Heads HSBC or HSBQ. This is a super duty flashtube for high power or Action Packs' fast flash duration. The Flashtubes push/pull straight in/out and they will last for tens of thousands of flashes or one face down fall onto a hard surface. Any of the Heads that have a modeling light would use the AFTE instead of this one.

The Straight Head Cable HC10 is about 10 feet long and has a male end that plugs towards the Power Pack and a female end that matches with the male plugs on the Flash Heads. This is a suitable way to extend the Head's built-in cable by an extra ten feet or to use a ten foot cable directly to the male plug on the Signature Series Heads.